Understanding DDR and DDR2 Memory

Memory Primer

DDR and DDR2 memory modules dominate the current desktop PC memory landscape. What are they and why are they different from the other memory types? Let’s find out.

DDR and DDR2 go by the full names of DDR SDRAM and DDR2 SDRAM respectively. The word “SDRAM” stands for Synchronous DRAM, which is a variant of DRAM (Dynamic RAM), a memory type widely used in PCs several years ago.

“RAM” stands for Random Access Memory. RAM is utilized in computer systems as main memory for temporary data storage. Most contemporary RAM is volatile, i.e. the information is lost once power is cut off. DRAM and SRAM (Static RAM) are the most popular RAM types used in computers. DRAM memory cells require constant refreshing because they utilize both transistors and capacitors; the latter of which loses the values it stores as time elapses if refreshing is not performed. Unlike DRAM, only transistors are used in SRAM memory cells, with no capacitors involved. SRAM, therefore, does not require refreshing, resulting in much higher performance. SRAM is much more expensive than DRAM, however, and is not used in the same memory sizes as DRAM. SRAM is implemented primarily in CPU caches (i.e. the CPU L1/L2 cache).

Going back to SDRAM, this type of memory utilizes a synchronous interface. This means it waits for a clock pulse to transfer data, and thus it is in sync with the computer system bus and the processor. SDRAM transfers one bit (per data line) of data per clock cycle to greatly improve the performance of system memory over previous FP/EDO memory, for which data transfer was possible only every other cycle. Typical PC100 and PC133 SDRAM modules provide maximum bandwidths of 800MB/s and 1066MB/s respectively.

DDR Basics

Short for “Double Data Rate”, DDR technology doubles the bandwidth of SDRAM under optimal conditions. This is to say that twice as much data can be transferred between the memory and system during the same amount of time. This is because DDR SDRAM sends and receives data twice as often as common SDRAM.

How does it do this? SDRAM transfers data on every clock cycle (to be specific, on the rising edge of every clock cycle), while DDR transfers data on both the rising edge (clock signal bounces from LOW to HIGH) and the falling edge (clock signal bounces from HIGH to LOW) of a clock cycle. Therefore, two bits (per data line) are transferred every clock cycle. In order to do this, two bits are accessed from the memory array (where data is actually stored) for each data line on every clock cycle, this process is called the “2-bit prefetch”.

A DDR200 module provides a data bandwidth of 1.6GB/s - we also call this PC1600 memory. Likewise, DDR400 is also called PC3200 memory, because it provides 3.2GB/s bandwidth. You can double the bandwidth by using same-speed memory modules in dual channel mode if your system supports it: dual channel DDR400 is capable of delivering 6.4GB/s bandwidth.

DDR2 Introduction

As 2nd generation DDR, the most important improvement found in DDR2 memory is its transfer data rate or bandwidth. As in the case with DDR SDRAM vs. SDRAM, the bandwidth of DDR2 memory can double the DDR’s.

The DDR standard stops at DDR400 (of course, there are lots of DDR500 and even DDR600 products on market, but these are for overclockers), which provides 3.2GB/s bandwidth (single channel). The DDR2 standard starts from DDR2 400 and goes all the way up to DDR2 800 or even higher. DDR2 800 or PC2 6400 can provide 6.4GB/s bandwidth (single channel), twice as much as DDR400. Dual channel DDR2 800 will offer an unparallel 12.8GB/s bandwidth, which is a huge leap from the 6.4GB/s bandwidth of dual channel DDR400 memory.

Since DDR already transfers data on both the rising and falling edges of a clock cycle, how does DDR2 double the bandwidth yet again? The answer lies in the I/O buffer frequency, which is doubled with DDR2. The memory controller in our systems only deal with the I/O buffer on the memory chip. To double the data from the memory array to the I/O buffer, DDR2 utilizes a “4-bit prefetch” as opposed to the “2-bit prefetch” with DDR. This means that 4 bits of data are moved from the memory array to the I/O buffer per data line each core clock cycle.

The core clock cycle here refers to the cycle time of the memory array, and the frequency of the memory array is half that of the I/O buffer and 1/4 of the data rates. Take DDR2 800 for example: it has an 800MHz data rate, the I/O buffer works at 400MHz, and the core frequency of the memory array is only 200MHz. The core frequency remains the same as DDR400. However, the DDR400 I/O buffer operates at 200MHz. The time of “a core cycle” is therefore the same whether it is DDR400 or DDR2 800.

DDR2 chips may look different than DDR as well, because most DDR chips use the TSOP-II (Thin Small-Outline Package) form factor while DDR2 utilizes the FBGA (Fine Ball Grid Array) form factor, which is smaller in size than TSOP-II. FBGA chips also feature less electrical noise than TSOP-II, thus resulting in improved signal integrity at high operating frequencies.

Here is a quick reference of differences between DDR and DDR2.

DDR DDR2
Data Rate 200/266/333/400 MHz
or higher
400/533/667/800 MHz
or higher
Prefetch Size 2-bit 4-bit
CAS latency 1.5, 2, 2.5, 3 3, 4, 5
Write Latency 1T Read Latency-1
Voltage 2.5V 1.8V
Package Type TSOP-II FGBA

Besides the enhanced bandwidth, DDR2 also uses less power than DDR by operating on 1.8V - a 28% reduction compared to DDR (2.5V). DDR2 has power saving features such as smaller page sizes and an active power down mode too. These power consumption advantages make DDR2 memory especially suitable for use in notebook computers.

DDR2 provides some other new features like OCT and OCD as well. We can find lots of resistors around the memory slots on a DDR-supporting motherboard, they are called termination resistors, which are used to eliminated excessive signal noise. You won’t find these resistors on motherboards utilizing DDR2 memory modules, since the termination resistors are built into each of the memory chips on the module, which is far closer to the source of the noise. This feature is called OCT or On-Die Termination, and it can reduce interference within the chip, thus guaranteeing the stability and reliability of DDR2 memory when working under high frequencies.

There are other features such as Posted CAS and Additive Latency, which work together to prevent data collisions and utilize the data bus more efficiently; and the Off-chip driver calibration (OCD), which increases signal integrity and system timing margin as well.

Readmore,..

View previously open folder after shutdown

Sometimes you want to access certain folders on your computer regularly, but if you have to always open those folder every time you turn on your computer, obviously it takes so much times. So, you can set them re-open automatically every time you turn on your computer. Here is the tip:

  1. Open My Computer
  2. Click Tools and then select Folder Option

clip_image002


3. If you can’t find the Folder Option on the Tools menu, just read the article about Recover Folder Option.

4. If you have clicked it, select View Tabs.

5. Look at the Advanced Setting area, scroll down to bottom and then give checkpoint on the Restore previous folder windows at logon, and then click OK.

6. Now and forever when you log on or restart, your computer will open the previously opened folder for you, as the same location before.

clip_image006

7. Now, when you turn on, restart or log on to your computer, your windows will automatically open the previously opened folder on your computer.

Readmore,..

Uninstall Windows Messenger

In this article I will show you how to uninstall Windows Messenger on your XP. Yes, for some people who already have MSN messenger on their XP apparently they don’t need 2 free messenger programs from Windows, because so far MSN messenger is better than Windows Messenger so I’ll show you how to uninstall Windows messenger that will save your drive space.

  1. First thing you need to do is go to drive C:, click twice on folder named Windows, and then click twice on ‘inf’ folder.
  2. After that, you need to find sysoc.inf , and click twice on it
  3. Now in this step you have to make some modification on the code. First you have to find this line on the component section.

msmsgs=msgrocm.dll,OcEntry,msmsgs.inf,hide,7

clip_image002

4. The next thing you have to do is delete the words ‘hide’. And it should now look like this:

msmsgs=msgrocm.dll,OcEntry,msmsgs.inf,,7

5.After you have done it, save the file and close it.

6. For uninstalling your Windows Messenger, go to Contol Panel – Add or Remove Windows Components. On the list you should see “Windows Messenger” Check the box beside it and click next and follow the next instruction.

7.Finally, you have done with your job. The last thing you need to do is just restart your computer to see the result.

Readmore,..

Partitioning your Hard Drive

For people who have computers, surely they don’t want to have only a hard drive in their computers. Instead, they need some hard drive (commonly 2 or 3) in their computer, so they can group their private data, system files, or their other stuff. So, an ability to partition hard drive is needed in order to group your stuff in your computer.

Disk partitioning is the creation of separate divisions of a hard disk drive using partition editors. Once a disk is divided into several partitions, directories and files of different categories may be stored in different partitions. More partitions provide more control but too many become cumbersome. The way space management, access permissions and directory searching are implemented depends upon the type of file system installed on a partition. Careful consideration of the size of the partition is necessary as the ability to change the size depends on the file system installed on the partition.

Partitioning your Hard Drive in Windows XP & Windows 2000:

  1. Right click on My Computer, then click Manage
  2. Then, Windows will open up Manage Screen. On the left pane, select Disk Management
  3. Usually, Windows will open up wizard to help partition and format your new drive. If it does not, right click the new drive in the lower pane and select initialize drive.

clip_image002

  1. Right click on the new drive and select new partition
  2. Then it will open up a wizard to help you partition your hard drive.
  3. In this step it will then prompt you how much drive space you want to allocate to the new partition.
  4. If you choose not to use the full space of your main hard drive for your new partition disk, you can make up additional partition in the same way up to 4 partition hard drive per disk.
  5. If you have done, you will be asked to name your partition. (C: , D: )
  6. After you named all of your partition, you have to format your new partition hard drive, which Windows will prompt to do automatically.
  7. If the formatting is complete, you have to reboot your computer to see the result.
Readmore,..

Before you buy laptop

At the moment, laptop is not a luxurious stuff for many people. Everyone owns laptop and everyone knows how to use it. Laptop is useful for the mobile person. But many people become hesitate when they are going to buy a laptop consider that laptop is not a low-priced stuff. Moreover, there are so many kinds of laptop offer different specs (specification) with different price also. Don’t worry, I tell you some tips which may guide you when you want to buy a new laptop. Here are 4 major tips you need to know before you buy laptop:

1. Consider between your budget and your purpose of buying laptop.

If your purpose of buying laptop is for gaming or designing, you have to choose the specification which offers high quality of VGA Cards, and also offers a high-speed memory.

For mobile person, you can focus on the battery, size of screen, and connectivity like: Wi-Fi, Bluetooth, IrDA, network card and modem.

2. Choose the longest time of warranty of laptop!

But you may consider with your budget.

3. Regardless of your purpose of buying new laptop, you should consider about the size of screen, weight of laptop, and the long-life of the battery.

If you often use your laptop on the road, you should choose a light laptop with a medium size of screen. It helps you feel comfort when you get used to travel somewhere.

You should also consider about the long-life of the battery. Mostly, laptop’s battery can last until 3 hours without being connected to adapter. If you want to economize the long-life of the battery, you may turn off the connectivity of your laptop like Wi-Fi or Bluetooth.

4. You should also consider about the selling-price of the laptop.

When you are going to buy a new laptop, you have to consider about its selling-price. I also recommend you not to buy a laptop which its spare parts are uneasy to find on the market.

I hope those tips will be helpful for you who are going to buy a new laptop. Thank you.

Readmore,..